This course introduces students to the basic components of electronics: diodes, transistors, and op amps. It covers the basic operation and some common applications.

Loading...

From the course by Georgia Institute of Technology

Introduction to Electronics

426 ratings

This course introduces students to the basic components of electronics: diodes, transistors, and op amps. It covers the basic operation and some common applications.

From the lesson

Op Amps Part 1

Learning Objectives: 1. Develop an understanding of the operational amplifier and its applications. 2. Develop an ability to analyze op amp circuits.

- Dr. Bonnie H. FerriProfessor

Electrical and Computer Engineering - Dr. Robert Allen Robinson, Jr.Academic Professional

School of Electrical and Computer Engineering

Welcome back to Electronics. This is Dr. Robinson.

Â In this lesson, I'm want to work an op-amp example problem where we solve for

Â the output voltage of an op-amp circuit.

Â Here's the schematic of the circuit, we're going to analyze.

Â Here's the input voltage, here's the output voltage of the circuit.

Â That's a two op-amp circuit.

Â Let's begin by noting that the voltage at the inverted terminal

Â of this op-amp is equal to the input voltage.

Â So the voltage at this node,

Â because of the ideal op-amp must also be equal to Vin.

Â We can calculate the current I through this R4 resistor as Vin divided by R4.

Â So, I is equal to Vin divided by R4 is equal V plus,

Â the voltage at the non-inverting terminal divided by R4.

Â Now to calculate the voltage at this node, let me label it V01,

Â the output voltage of this op-amp.

Â We'll start with this node voltage and add the IR drop across R3.

Â So, I say that V01 is equal to

Â V plus at the non-inverting terminal

Â plus I times R3 is equal to Vin

Â plus Vin over R4 times R3.

Â Now let's introduce Vout, the voltage we were trying to solve for

Â into our set of equations by writing a node equation at this node.

Â So, I can write that V01 minus 0 over R2,

Â the current through this resistor,

Â plus the 0 or Vout minus 0 over R1 is equal to 0.

Â Which implies that V01 over R2 is

Â equal to negative Vout over R1 or

Â V01 is equal to negative R2 over R1

Â times the output voltage, Vout.

Â Now we know that V01 is equal to Vin plus Vin times R3 over R4.

Â So, I'm going to make that substitution into this equation.

Â So, I can write that Vin plus Vin times R3 over

Â R4 is equal to negative R2 over R1 times the output voltage, Vout.

Â Now, on this side of this equation, I can factor Vin out, bring it to

Â this side to solve for the ratio would be Vout to Vin or the gain of the circuit.

Â So, I can write that Vout over

Â Vin is equal to negative R1 over

Â R2 times 1 plus R3 over R4.

Â The answer.

Â Now, let's rework this problem in another way where we use known results to

Â simplify our analysis.

Â Now we recognize that this portion of the circuit is an inverting op-amp amplifier,

Â so we know the relationship between V01 and Vout.

Â VO1 is equal to negative R2 over R1 time Vout.

Â Then we recognize this portion of the circuit as a two resistor voltage divider,

Â where the output voltage here is equal to the input voltage times R4 over R3

Â plus R4.

Â And because of this ideal op-amp, we know that the voltage here must be equal to

Â the voltage here, which is equal to Vin.

Â So we can write by inspection that

Â Vin is equal to Vout times negative

Â R2 over R1 times R4 over R3 plus R4.

Â Where again, Vout times negative R2 over R1 is equal to VO1 and

Â VO1 is the input to the voltage divider with a gain of R4 over R3 plus R4.

Â So V01 is this portion, we multiply by the voltage divider to get the voltage here,

Â which is equal to Vin, because of this idea op-amp.

Â Then we can write that V0 is equal to or

Â V0 over Vin is equal to negative

Â R1 over R2 times 1 plus R3 over R4.

Â The same answer we obtained previously.

Â Now let's look at something to note about this circuit.

Â It may appear at first, that this circuit does not have negative feedback and

Â because of that, we cannot consider the voltage at the inverting terminal

Â to be equal to the voltage at the non-inverting terminal.

Â You can see that there's no path from the output voltage to the inverting terminal.

Â In fact, there's a path from the output voltage to the non-inverting terminal,

Â which may appear initially to be positive feedback.

Â But in this path between the output voltage and

Â the non-inverting terminal is an inverting op-amp that introduces a negative sign.

Â So this path from output to non-inverting terminal is actually a negative feedback

Â path and because of that, the voltage at the inverting terminal is

Â equal to the voltage at the non-inverting terminal.

Â Coursera provides universal access to the worldâ€™s best education,
partnering with top universities and organizations to offer courses online.